HP ProCurve 2610-24 Скачать руководство пользователя страница 406 | Manualshive

Страница: 406 / 464

background image

Troubleshooting

Unusual Network Activity

The public key file you are trying to download has one of the following
problems:

■

A key in the file is too long. The maximum key length is 1024 characters,
including spaces. This could also mean that two or more keys are merged
together instead of being separated by a <CR><LF>.

■

There are more than ten public keys in the key file.

■

One or more keys in the file is corrupted or is not a valid rsa public key.

Client ceases to respond (“hangs”) during connection phase.

The

switch does not support data compression in an SSH session. Clients will often
have compression turned on by default, but will disable it during the negotia
tion phase. A client which does not recognize the compression-request FAIL
URE response may fail when attempting to connect. Ensure that compression
is turned off before attempting a connection to prevent this problem.

Stacking-Related Problems

The Stack Commander Cannot Locate any Candidates.

Stacking oper

ates on the primary VLAN, which in the default configuration is the
DEFAULT_VLAN. However, if another VLAN has been configured as the
primary VLAN, and the Commander is not on the primary VLAN, then the
Commander will not detect Candidates on the primary VLAN.

TACACS-Related Problems

Event Log.

When troubleshooting operation, check the switch’s

Event Log for indications of problem areas.

All Users Are Locked Out of Access to the Switch.

If the switch is func

tioning properly, but no username/password pairs result in console or Telnet
access to the switch, the problem may be due to how the server
and/or the switch are configured. Use one of the following methods to recover:

■

Access the server application and adjust or remove the
configuration parameters controlling access to the switch.

■

If the above method does not work, try eliminating configuration
changes in the switch that have not been saved to flash (boot-up
configuration) by causing the switch to reboot from the boot-up
configuration (which includes only the configuration changes made
prior to the last

write memory

command.) If you did not use

write

C-16

«
...
404
405
406
407
408
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

xStack DGS-3420 Series

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 29

Бренд: D-Link Страницы: 454

Бренд: D-Link Страницы: 502

Бренд: D-Link Страницы: 244

Бренд: D-Link Страницы: 20

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 37

Бренд: D-Link Страницы: 28

SUPERSTACK 3 3226

Бренд: 3Com Страницы: 5

Бренд: 3Com Страницы: 139

CoreBuilder 7000

Бренд: 3Com Страницы: 150

CoreBuilder 7000

Бренд: 3Com Страницы: 264

Бренд: 3Com Страницы: 574

Бренд: 3Com Страницы: 333

SUPERSTACK 3 3226

Бренд: 3Com Страницы: 70

OfficeConnect 3C16790C

Бренд: 3Com Страницы: 18

Бренд: 3Com Страницы: 1314

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды