HP ProCurve 2610-24 Скачать руководство пользователя страница 408 | Manualshive

Страница: 408 / 464

background image

Troubleshooting

Unusual Network Activity

■

The access attempt is outside of the time frame allowed for the
account.

■

The allowed number of concurrent logins for the account has been
exceeded

For more help, refer to the documentation provided with your
server application.

Unknown Users Allowed to Login to the Switch.

Your appli

cation may be configured to allow access to unknown users by assigning them
the privileges included in a

default user

profile. Refer to the documentation

provided with your server application.

System Allows Fewer Login Attempts than Specified in the Switch
Configuration.

Your server application may be configured to

allow fewer login attempts than you have configured in the switch with the

aaa authentication num-attempts

command.

TimeP, SNTP, or Gateway Problems

The Switch Cannot Find the Time Server or the Configured Gateway .

TimeP, SNTP, and Gateway access are through the primary VLAN, which in
the default configuration is the DEFAULT_VLAN. If the primary VLAN has
been moved to another VLAN, it may be disabled or does not have ports
assigned to it.

VLAN-Related Problems

Monitor Port.

When using the monitor port in a multiple VLAN environ

ment, the switch handles broadcast, multicast, and unicast traffic output from
the monitor port as follows:

■

If the monitor port is configured for tagged VLAN operation on the same
VLAN as the traffic from monitored ports, the traffic output from the
monitor port carries the same VLAN tag.

■

If the monitor port is configured for untagged VLAN operation on the same
VLAN as the traffic from the monitored ports, the traffic output from the
monitor port is untagged.

■

If the monitor port is not a member of the same VLAN as the traffic from
the monitored ports, traffic from the monitored ports does not go out the
monitor port.

C-18

«
...
406
407
408
409
410
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: D-Box Страницы: 27

DES-3224 - Switch

Бренд: D-Link Страницы: 75

Бренд: Zektor Страницы: 65

Infinity IES-1881

Бренд: LevelOne Страницы: 2

Бренд: Delta Electronics Страницы: 1

MicroHub GUH274W3

Бренд: IOGear Страницы: 1

Бренд: JAR Systems Страницы: 2

Бренд: Surefire Страницы: 2

CT.TS005.003902

Бренд: Talkswitch Страницы: 309

Бренд: Nextech Страницы: 4

3CB9E7 - CoreBuilder 9000 Chassis Switch

Бренд: 3Com Страницы: 132

iBootBar iBB-DC8

Бренд: Dataprobe Страницы: 36

Бренд: ZIMCO Страницы: 7

Бренд: Goobay Страницы: 2

enbrighten 51253

Бренд: Jasco Страницы: 2

IntraCore IC39240

Бренд: Asante Страницы: 3

Бренд: Alloy Страницы: 13

Бренд: Pakedge Device & Software Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды