HP ProCurve 2610-24 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 464

background image

Using the Web Browser Interface

Starting a Web Browser Interface Session with the Switch

Using ProCurve Manager (PCM) or ProCurve Manager
Plus (PCM+)

ProCurve Manager and ProCurve Manager Plus are designed for installation
on a network management workstation. For this reason, the system require
ments are different from the system requirements for accessing the switch’s
web browser interface from a non-management PC or workstation. For
ProCurve PCM and PCM+ requirements, refer to the information provided
with the software.

This procedure assumes that:

■

You have installed the recommended web browser on a PC or workstation
that serves as your network management station.

■

The networked device you want to access has been assigned an IP address
and (optionally) a DNS name, and has been discovered by PCM or PCM+.
(For more on assigning an IP address, refer to “IP Configuration” on page
8-3.)

To establish a web browser session with ProCurve PCM or PCM+ running, do
the following on the network management station:

1. Make sure the Java

TM

applets are enabled for your web browser. If they

are not, refer to the web browser online Help for specific information on
enabling the Java applets.

2. In the

Interconnected Devices

listing under

Network Manager Home

(in the

PCM/PCM+ sidebar), right-click on the model number of the device you
want to access.

3. The web browser interface automatically starts with the Status Overview

window displayed for the selected device, as shown in figure 5-1.

N o t e

If the Registration window appears, click on the

Status

tab.

5-5

«
...
73
74
75
76
77
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: E-T-A Страницы: 6

Бренд: DANLERS Страницы: 2

Бренд: socomec Страницы: 78

Бренд: PureLink Страницы: 10

DL-DVI-MUX2-NT SERIES

Бренд: G&D Страницы: 76

Бренд: Key Digital Страницы: 31

JTECH-4KPIP0401

Бренд: J-Tech Digital Страницы: 10

Бренд: Cable Electronics Страницы: 12

Signal Distribution Box SDB45

Бренд: Audiovox Страницы: 12

Бренд: Eaton Страницы: 3

Бренд: ZIMCO Страницы: 7

Бренд: Goobay Страницы: 2

Бренд: Anker Страницы: 16

Бренд: IOGear Страницы: 54

Бренд: Resource Data Management Страницы: 14

ServSwitch Simplicity

Бренд: Black Box Страницы: 2

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды