manualshive.com logo in svg

HP ProCurve 2610-24, Руководство по управлению и настройке

HP ProCurve 2610-24 - сетевой коммутатор с широким функционалом и возможностями для настройки и управления сетью. Управляйте устройством с помощью Management And Configuration Manual, которое можно бесплатно скачать на manualshive.com. Идеальный выбор для оптимизации работы вашей сети.

Поделиться
Скачать
background image

Troubleshooting 

Unusual Network Activity 

Spanning-Tree Protocol (STP) and Fast-Uplink 
Problems 

C a u t i o n    

If you enable STP, it is recommended that you leave the remainder of the STP 
parameter settings at their default values until you have had an opportunity 
to evaluate STP performance in your network. Because incorrect STP settings 
can adversely affect network performance, you should avoid making changes 
without having a strong understanding of how STP operates. To learn the 
details of STP operation, refer to the IEEE 802.1D standard. 

Broadcast Storms Appearing in the Network. 

This can occur when 

there are physical loops (redundant links) in the topology.Where this exists, 
you should enable STP on all bridging devices in the topology in order for the 
loop to be detected. 

STP Blocks a Link in a VLAN Even Though There Are No Redundant 
Links in that VLAN. 

In 802.1Q-compliant devices such as the switches cov­

ered by this guide, STP blocks redundant physical links even if they are in 
separate VLANs. A solution is to use only one, multiple-VLAN (tagged) link 
between the devices. Also, if ports are available, you can improve the band­
width in this situation by using a port trunk. See the chapter on VLANs in the 

Advanced Traffic Management Guide

.. 

Fast-Uplink Troubleshooting.  

Some of the problems that can result from 

incorrect usage of Fast-Uplink STP include temporary loops and generation 
of duplicate packets. 

Problem sources can include: 

■

  

Fast-Uplink is configured on a switch that is the STP root device. 

■

  

Either the 

Hello Time

 or the 

Max Age 

setting (or both) is too long on one or 

more switches. Return the 

Hello Time

 and Max Age settings to their default 

values (2 seconds and 20 seconds, respectively, on a switch). 

■

  

A “downlink” port is connected to a switch that is further away (in hop 
count) from the root device than the switch port on which fast-uplink STP 
is configured. 

■

  

Two edge switches are directly linked to each other with a fast-uplink 
(Mode = 

Uplink

) connection. 

■

  

Fast uplink is configured on both ends of a link. 

■

  

A switch serving as a backup STP root switch has ports configured for 
fast-uplink STP and has become the root device due to a failure in the 
original root device. 

C-14 

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

TAMS 1800 Series Installation & Operation Manual preview
1800 Series
Бренд: TAMS Страницы: 28
NETGEAR DS104 Installation Manual preview
DS104
Бренд: NETGEAR Страницы: 15
Panasonic WJSX150 - SWITCHER - ADDENDUM Addendum preview
WJSX150 - SWITCHER - ADDENDUM
Бренд: Panasonic Страницы: 48
Cabletron Systems MMAC-Plus 9G426-02 Reference Manual preview
MMAC-Plus 9G426-02
Бренд: Cabletron Systems Страницы: 12
Cabletron Systems MMAC-Plus 9F310-02 Appendix preview
MMAC-Plus 9F310-02
Бренд: Cabletron Systems Страницы: 4
Cabletron Systems 9E423-36 Owner'S Manual preview
9E423-36
Бренд: Cabletron Systems Страницы: 16
cable matters 101065 Quick Start Manual preview
101065
Бренд: cable matters Страницы: 4
CableCreation CD0395 User Manual preview
CD0395
Бренд: CableCreation Страницы: 7
G&D DVIMUX4-DL-USB Installation And Operations preview
DVIMUX4-DL-USB
Бренд: G&D Страницы: 36
Nectarine Health Satellite Manual preview
Satellite
Бренд: Nectarine Health Страницы: 9
UNICOM DynaGST/2402G GEP-33224T-1 Specifications preview
DynaGST/2402G GEP-33224T-1
Бренд: UNICOM Страницы: 1
UNICONTROL Electronic Cleveland Controls RSS-498-013 Manual preview
Cleveland Controls RSS-498-013
Бренд: UNICONTROL Electronic Страницы: 2
Zigen SW-42Plus User Manual preview
SW-42Plus
Бренд: Zigen Страницы: 40
Zigen SW-41Plus Quick Start Manual preview
SW-41Plus
Бренд: Zigen Страницы: 4
Kramer VS-421 User Manual preview
VS-421
Бренд: Kramer Страницы: 8
Jasco AS2006 Manual preview
AS2006
Бренд: Jasco Страницы: 2
Generac Power Systems GenReady Series 005448-2 Overview preview
GenReady Series 005448-2
Бренд: Generac Power Systems Страницы: 4
Kohler VERSO50 User Manual preview
VERSO50
Бренд: Kohler Страницы: 170

Бренды по названию

Популярные бренды

Загрузить еще бренды