manualshive.com logo in svg

HP ProCurve 2610-24, Руководство по управлению и настройке

HP ProCurve 2610-24 - сетевой коммутатор с широким функционалом и возможностями для настройки и управления сетью. Управляйте устройством с помощью Management And Configuration Manual, которое можно бесплатно скачать на manualshive.com. Идеальный выбор для оптимизации работы вашей сети.

Поделиться
Скачать
background image

Using the Web Browser Interface 

Starting a Web Browser Interface Session with the Switch 

Starting a Web Browser Interface 
Session with the Switch 

You can start a web browser session in the following ways: 

■

  

Using a standalone web browser on a network connection from a PC or 
UNIX workstation: 

•   Directly connected to your network 

•   Connected through remote access to your network 

■

  

Using a management station running ProCurve Manager on your network 

Using a Standalone Web Browser in a PC or UNIX 
Workstation 

This procedure assumes that you are using a compatible web browser (see 
the software 

Release Notes 

for more information) and that the switch is 

configured with an IP address accessible from your PC or workstation. (For 
more on assigning an IP address, refer to “IP Configuration” on page 8-3.) 

1.   Ensure that the Java

TM 

applets are enabled for your browser. For more 

information on this topic, refer to your browser’s online Help. 

2.   Use the web browser to access the switch. If your network includes a 

Domain Name Server (DNS), your switch’s IP address may have a name 
associated with it (for example, 

switch5308

) that you can type in the 

Location or Address 

field instead of the IP address. Using DNS names 

typically improves browser performance. Contact your network adminis­
trator to enquire about DNS names associated with your ProCurve switch. 

Type the IP address (or DNS name) of the switch in the browser 

Location 

or 

Address

 (URL) field and press 

[Enter]

. (It is not necessary to include 

http:/ 

/

.) 

switch5308 

[Enter] 

(example of a DNS-type name) 

10.11.12.195 

[Enter] 

(example of an IP address) 

5-4 

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

D-Link DSS-16+ Reference Manual preview
DSS-16+
Бренд: D-Link Страницы: 2
3Com 4007 Release Note preview
4007
Бренд: 3Com Страницы: 128
3Com 4005 Datasheet preview
4005
Бренд: 3Com Страницы: 2
3Com 4200G 12-Port Configuration Manual preview
4200G 12-Port
Бренд: 3Com Страницы: 422
3Com 3CR16708-91 - OfficeConnect Managed Switch 9 Datasheet preview
3CR16708-91 - OfficeConnect Managed Switch 9
Бренд: 3Com Страницы: 4
3Com 3CR13501-73 Release Note preview
3CR13501-73
Бренд: 3Com Страницы: 5
3Com 3CR13500 Software Install Manual preview
3CR13500
Бренд: 3Com Страницы: 30
3Com 5500G SERIES Getting Started Manual preview
5500G SERIES
Бренд: 3Com Страницы: 36
3Com 3CNJ220-CRM Datasheet preview
3CNJ220-CRM
Бренд: 3Com Страницы: 4
3Com Baseline 2226-PWR Plus User Manual preview
Baseline 2226-PWR Plus
Бренд: 3Com Страницы: 77
3Com 3CRWX120695A Reference Manual preview
3CRWX120695A
Бренд: 3Com Страницы: 570
3Com OfficeConnect WX1200 Release Note preview
OfficeConnect WX1200
Бренд: 3Com Страницы: 28
3Com Baseline 2226-PWR Plus Datasheet preview
Baseline 2226-PWR Plus
Бренд: 3Com Страницы: 4
3Com CoreBuilder 6000 Supplementary Manual preview
CoreBuilder 6000
Бренд: 3Com Страницы: 31
EtherWAN EX62000 Installation Manual preview
EX62000
Бренд: EtherWAN Страницы: 2
Inscape Data Link Power LPS2400-T1 User Manual preview
Link Power LPS2400-T1
Бренд: Inscape Data Страницы: 8
Lindy 32 277 Installation And Use Manual preview
32 277
Бренд: Lindy Страницы: 38
QCT QuantaMesh T4000 Series Installation Manual preview
QuantaMesh T4000 Series
Бренд: QCT Страницы: 41

Бренды по названию

Популярные бренды

Загрузить еще бренды