HP ProCurve 2610-24 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 464

background image

Using the Menu Interface

Starting and Ending a Menu Session

N o t e

If the switch has neither a Manager nor an Operator password, anyone
having access to the console interface can operate the console with full
manager privileges. Also, if you configure only an Operator password,
entering the Operator password enables full manager privileges.

For more information on passwords, see the chapter on local passwords in
the Access Security Guide for your switch.

■

The menu interface displays the current running-config parameter set
tings. You can use the menu interface to save configuration changes made
in the CLI only if the CLI changes are in the running config when you save
changes made in the menu interface. (For more on how switch memory
manages configuration changes, see Chapter 6, “Switch Memory and
Configuration”.)

■

A configuration change made through any switch interface overwrites
earlier changes made through any other interface.

■

The Menu Interface and the CLI (Command Line Interface) both use the
switch console. To enter the menu from the CLI, use the

menu

command.

To enter the CLI from the Menu interface, select

Command Line (CLI)

option.)

Starting and Ending a Menu Session

You can access the menu interface using any of the following:

■

A direct serial connection to the switch’s console port, as described in the
installation guide you received with the switch

■

A Telnet connection to the switch console from a networked PC or the
switch’s web browser interface. Telnet requires that an IP address and
subnet mask compatible with your network have already been configured
on the switch.

■

The stack Commander, if the switch is a stack member

N o t e

This section assumes that either a terminal device is already configured and
connected to the switch (see the

Installation and Getting Started Guide

shipped with your switch) or that you have already configured an IP address
on the switch (required for Telnet access).

3-3

«
...
39
40
41
42
43
...
»

Содержание ProCurve 2610-24

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProCurve 2610-24

Бренд: Patton electronics Страницы: 104

Бренд: steute Страницы: 20

Бренд: N-Tron Страницы: 132

Бренд: Imtex-Controls Страницы: 2

Бренд: VeEX Страницы: 22

Magnum CS14 Series

Бренд: GarrettCom Страницы: 76

Бренд: AbleNet Страницы: 6

Бренд: Optex Страницы: 2

Бренд: Hall Research Technologies Страницы: 9

Бренд: Televes Страницы: 24

Бренд: Lancom Страницы: 21

Бренд: Racal Instruments Страницы: 53

Vertical Horizon VH-2402-L3

Бренд: Enterasys Страницы: 201

Бренд: Linksys Страницы: 4

Бренд: EnGenius Страницы: 72

Бренд: SMART-AVI Страницы: 8

ATLONA AT-HDR-SW-51

Бренд: Panduit Страницы: 58

Бренд: Fujitsu Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды