Fibocom L860-GL Скачать руководство пользователя

Страница: 64 / 254

FIBOCOM L860 AT Commands User Manual

Page 64 of 254

Command

Description

[Response/Action]

or:

+CME ERROR: <err>

Read

[Function]

The Read command returns the current date, time and time zone setting.

By default, <time> will represent the network updated time.

If the user has used the Set command once, then <time> will represent the Set

command setting.

Note:

If network operator does not support System Clock Update Message, the

initial date, time and time zone, displayed by CCLK Read Command could

be invalid (user's responsibility to set date, time and time zone by CCLK Set

Command).

Note:

See Execute Command for how-to enable back network update time.

[Syntax]

AT+CCLK?

[Response/Action]

+CCLK: <time>

or:

+CME ERROR: <err>

Test

[Function]

The Test command returns valid parameters for the +CCLK Set command.

[Syntax]

AT+CCLK=?

[Response/Action]

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды