Fibocom L860-GL Скачать руководство пользователя страница 53

Страница: 53 / 254

FIBOCOM L860 AT Commands User Manual

Page 53 of 254

Command

Description

<High> (-)–0 - 125; The Highest boundary level of the temperature value for

unsolicited report.

(Default value = 0 Celsius).

Setting corresponding <Low> and <High> temperature boundaries for <Report>=3

only.

Example

AT+MTSM=?

// Test the range of the parameters.

+MTSM: (0-3,6-7),(1-255),(-40-125)

AT+MTSM=1

// Set to read for once the current temperature measurement.

+MTSM: 35

// Current temperature is +35 Celsius degree.

AT+MTSM=2,5

// Set to unsolicited temperature reports to TE for every 5 seconds.

+MTSM: -10

// Current temperature measure report -10 Celsius.

+MTSM: -5

// Unsolicited temperature report -5 Celsius after 5 seconds.

+MTSM: 7

// Unsolicited temperature measure 7 Celsius after 10 seconds.

+MTSM: 20 // Unsolicited temperature measure 20 Celsius after 15 seconds.

…

+MTSM: 50 // Unsolicited temperature measure 50 Celsius after Nx5 seconds.

AT+MTSM=0

// Set to stop the unsolicited report.

AT+MTSM=3,30,-10,40

// Set to out-off boundary (-10 to +40 Celsius)

unsolicited reports for every 30 seconds.

+MTSM: -20

// Unsolicited current report out-off the Low boundary.

+MTSM: -12

// Unsolicited report out-off the Low boundary after 30 seconds.

+MTSM: 47

// Unsolicited report out-off the High boundary after Nx30 seconds

AT+MTSM?

// Read the current setting.

+MTSM: 3,30,-10,40

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды