Fibocom L860-GL страница 117 Скачать руководство пользователя

Страница: 117 / 254

FIBOCOM L860 AT Commands User Manual

Page 117 of 254

+CUSATD=1,1) or that it is ready for profile download (sCUSATD=2,1). In both cases, the MT also

indicates the end of UICC start-up by the unsolicited result code +CUSATS: 4. If the UICC is awaiting PIN

verification during start-up, this is also reported.

When using +CUSATD=1, the +CUSATA=1 command has to be used to enable TE profile facility handling

after restart. In the time between profile download and issuance of +CUSATA=1, the UICC may already

attempt to issue proactive commands. The MT will not send these to the TE, but rather give the UICC the

response "terminal currently unable to process command" autonomously. The UICC may implement only

a limited number of retries, which can potentially leave USAT in an unwanted state if the +CUSATA=1

command arrives late.

Note:

Care has to be taken when using +CUSATD=2. If no +CUSATA=2 or +CUSATA=3 is sent during

start-up, USAT is also blocked for the MT.

Command

Description

Set

[Function]

Set command The command without parameters resets the parameters to their default

values. Enables which profile needs to be downloaded during next bootup.

[Syntax]

AT+CUSATD=[<download>[,<reporting>]]

[Response/Action]

+CME ERROR: <err>

Read

[Function]

Read command returns the current <download> and <reporting>

[Syntax]

AT+CUSATD?

[Response/Action]

+CUSATD: <download>,<reporting>

Test

[Function]

Test command returns values supported as a compound value.

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды