Fibocom L860-GL страница 225 Скачать руководство пользователя

Страница: 225 / 254

FIBOCOM L860 AT Commands User Manual

Page 225 of 254

Command

Description

<d_comp>

(A numeric parameter that controls PDP data compression (applicable

for SNDCP only))

0 off (default if value is omitted)

1 on (manufacturer preferred compression)

2 V.42 bis

Other values are reserved.

<h_comp>

(A numeric parameter that controls PDP header compression)

0 off (default if value is omitted)

1 on (manufacturer preferred compression)

2 RFC1144 (applicable for SNDCP only)

3 RFC2507

4 RFC3095 (applicable for PDCP only)

Other values are reserved.

<IM_CN_Signaling_Flag_Ind>

a numeric parameter used to indicate to the network whether the PDP context is

for IM CN subsystem-related signaling only or not.

0 UE indicates that the PDP context is not for IM CN subsystem-related Signaling only

1 UE indicates that the PDP context is for IM CN subsystem-related Signaling only

Note:

The parameter <IM_CN_Signaling_Flag_Ind> , can be over-ridden by

AT+XPCO command (meaning AT+CGDSCONT values for these

parameters can be over-ridden by issuing AT+XPCO later).

Example

Reference

3GPP TS 27.007

11.2.17 +CGEREP

，

Packet Domain Event Reporting

This command is used to enable or disable sending of unsolicited result codes, +CGEV: XXX from MT to

TE in the case of events occurring in the Packet Domain.

Command

Description

Set

[Function]

The Set command enables or disables sending of unsolicited result codes, +CGEV:

XXX from MT to TE in the case of certain events occurring in the Packet Domain MT or

the network.

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды