Fibocom L860-GL Скачать руководство пользователя

Страница: 240 / 254

FIBOCOM L860 AT Commands User Manual

Page 240 of 254

Command

Description

[Syntax]

AT+CGTFTRDP=?

[Response/Action]

+CGTFTRDP: (list of <cid>s associated with active contexts)

Parameters

<cid>:

a numeric parameter which specifies a particular PDP context definition or Traffic

Flows definition (see +CGDCONT and +CGDSCONT commands).

The following parameters are defined in 3GPP TS 23.060 [47]

<packet filter identifier>:

a numeric parameter. The value range is from 1 to 16.

<evaluation precedence index>:

a numeric parameter. The value range is from 0 to 255.

<source address and subnet mask>:

string type. The string is given as dot-separated numeric (0-255) parameters on the

form:

"a1.a2.a3.a4.m1.m2.m3.m4" for Ipv4 or

"a1.a2.a3.a4.a5.a6.a7.a8.a9.a10.a11.a12.a13.

a14.a15.a16.m1.m2.m3.m4.m5.m6.m7.m8.m9.m10.m11.m12.m13.m14.m15.m16",

for Ipv6.

Note:

IPv6 address obtained on LTE will be prefixed with a constant 8 byte

address "FE.80.00.00.00.00.00.00" if network has not provided.

<protocol number (ipv4) / next header (ipv6)>:

a numeric parameter, value range from 0 to 255.

<destination port range>:

string type. The string is given as dot-separated numeric (0-65535) parameters on the

form "f.t".

<source port range>:

string type. The string is given as dot-separated numeric (0-65535) parameters on the

form "f.t".

<ipsec security parameter index (spi)>:

numeric value in hexadecimal format. The value range is from 00000000 to

FFFFFFFF.

<type of service (tos) (ipv4) and mask / traffic class (ipv6) and mask>:

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды