Fibocom L860-GL Скачать руководство пользователя страница 115

Страница: 115 / 254

FIBOCOM L860 AT Commands User Manual

Page 115 of 254

unchanged. The MT responds with +CUSATW : <profile_storage>,<conflict_profile> where

<profile_storage> refers the conflicting profile followed by the final result code +CME ERROR: 3

(Operation not allowed). The rules for detecting conflicts are defined in 3GPP TS 31.111 [92].

Successful execution of the command does not result in any information response.

Command

Description

Set

[Function]

Set command without parameters resets stored TE and MT profiles to their default

values. Adding parameter <profile_storage> to the AT command resets only the

referred storage to its default value. Execution command issued with accompanied

parameter <profile>, stores the given <profile> to non-volatile memory in the MT.

[Syntax]

AT+CUSATW[=<profile_storage>[,<profile>]]

[Response/Action]

+CUSATW: <profile_storage>,<profile>[<CR><LF>+cusatw:

<profile_storage>,<profile>

[...]]

+CME ERROR: <err>

Read

N/A

Test

[Function]

Test command returns values supported as a compound value.

[Syntax]

AT+CUSATW=?

[Response/Action]

+CUSATW: (list of supported <profile_storage>s)

Parameters

<profile_storage>

Is an integer type.

0 TE. Refers profile storage for the facilities supported by the TE. Default value is a

blank profile with all bits set to zero.

1 MT. Refers profile storage for the facilities to be

supported by MT, which can be a subset of the default MT facilities (see +CUSATW).

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды