Fibocom L860-GL Скачать руководство пользователя

Страница: 73 / 254

FIBOCOM L860 AT Commands User Manual

Page 73 of 254

Command

Description

Parameters

<mem1> Memory from which messages are read and deleted.

Supported values are: "SM",”BM”,”ME”,”SR”.

The default value at power-up is "SM".

<mem2> Memory to which writing operation is made.

Supported value is: "SM".

The default value at power-up is "SM".

<mem3> Memory to which received SMS are stored (unless forwarded directly to TE).

Supported value is: "SM","BM",”SR”

The default value at power-up is "SM".

"BM"

Broadcast message storage

"SM"

(U)SIM message storage

"ME"

ME message storage

"SR"

status report storage

Note:

L8 family products support only “SM” storage for all areas.

Example

AT+CPMS="SM"

+CPMS: 5,50,5,50,5,50

AT+CPMS?

+CPMS: "SM",5,50,"SM",5,50,"SM",5,50

Reference

3GPP TS 27.005

6.1.3 +CMGF, Message Format

This command is a basic command.

The Set command handles the selection of the message format used with send, list, read and write

commands, as well as the format of unsolicited result codes resulting from message receipts.

The Modem supports both PDU mode (where entire TP data units are used) and text mode (where the

body of the message and its headers are given as separate parameters).

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды