Fibocom L860-GL страница 226 Скачать руководство пользователя

Страница: 226 / 254

FIBOCOM L860 AT Commands User Manual

Page 226 of 254

Command

Description

[Syntax]

AT+CGEREP=[<mode>[,<bfr>]]

[Response/Action]

Read

[Function]

The read command returns the current value of <mode> and <bfr> parameters.

[Syntax]

AT+CGEREP?

[Response/Action]

+CGEREP: <mode>, <bfr>

Test

[Function]

The test command lists the supported values for <mode> and for <bfr>.

[Syntax]

AT+CGEREP=?

[Response/Action]

+CGEREP: (list of supported <mode>s),(list of supported <bfr>s)

Parameters

<mode>

0 buffer unsolicited result codes in the MT; if MT result code buffer is full, the oldest

ones can be discarded. No codes are forwarded to the TE.

1 discard unsolicited result codes when MT-TE link is reserved (e.g. in on-line data

mode); otherwise forward them directly to the TE

2 buffer unsolicited result codes in the MT when MT-TE link is reserved (e.g. in

on-line data mode) and flush them to the TE when MT-TE link becomes available;

otherwise forward them directly to the TE

<bfr>

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды