Fibocom L860-GL Скачать руководство пользователя страница 235

Страница: 235 / 254

FIBOCOM L860 AT Commands User Manual

Page 235 of 254

Command

Description

AT+CGPADDR=1

+CGPADDR: 1,"10.24.128.144","254.128.0.0.0.0.0.0.74.48.152.30.172.122.220.28"

Reference

3GPP TS 27.007

11.2.21 +CGCONTRDP, PDP Context Read Dynamic Parameters

Command

Description

Set

[Function]

The set command returns the relevant information about <bearer_id>, <apn>,

<source_addr and subnet_mask>, <gw_addr>, <DNS_prim_addr>, <DNS_sec_addr>,

<P-CSCF_prim_addr>, <P-CSCF_sec_addr> and <IM_CN_Signalling_Flag> for a non

secondary PDP Context established by the network with the primary context identifier

<cid>. If the context cannot be found an ERROR response is returned. If the MT has

dual stack capabilities, two lines of information are returned per <cid>. First one line with

the IPv4 parameters followed by one line with the IPv6 parameters. If the parameter

<cid> is omitted, the relevant information for all established PDP contexts are returned.

[Syntax]

AT+CGCONTRDP= [<cid>]

[Response/Action]

+CGCONTRDP: <cid>, <bearer_id>, <apn> [,<source_addr and subnet_mask>[,

<gw_addr>[, <DNS_prim_addr>[, <DNS_sec_addr>[, <PCSCF_prim_addr>[,

<P-CSCF_sec_addr>[,<IM_CN_Signalling_Flag>]]]]]]]

[<CR><LF>+CGCONTRDP: <cid>, <bearer_id>,<apn> [,<source_addr and subnet

mask>[, <gw_addr>[, <DNS_prim_addr>[, <DNS_sec_addr>[, <P-CSCF_prim_addr>[,

<P-CSCF_sec_addr>[,<IM_CN_Signalling_Flag>]]]]]]]

[...]]

Read

N/A

Test

[Function]

The test command returns a list of <cid>s associated with active contexts

[Syntax]

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды