Fibocom L860-GL страница 216 Скачать руководство пользователя

Страница: 216 / 254

FIBOCOM L860 AT Commands User Manual

Page 216 of 254

Command

Description

<SDU error ratio> a string parameter that indicates the target value for the fraction of

SDUs lost or detected as erroneous. SDU error ratio is defined only for conforming

traffic. The value is specified as ‘mEe’. As an example

a target SDU error ratio of 5•10-3 would be specified as ‘5E3’ (e.g.

AT+CGEQREQ=…,”5E3”,…). ‘0E0’ means subscribed value (refer 3GPP TS 24.008

subclause 10.5.6.5).

<Residual bit error ratio> a string parameter that indicates the target value for the

undetected bit error ratio in the delivered SDUs. If no error detection is requested,

Residual bit error ratio indicates the bit error ratio in the delivered SDUs. The value is

specified as ‘mEe’. As an example a target residual bit error ratio of 5•10-3 would be

specified as ‘5E3’ (e.g. AT+CGEQREQ=…,”5E3”,…). ‘0E0’ means subscribed value

(refer 3GPP TS 24.008 subclause 10.5.6.5).

<Delivery of erroneous SDUs> a numeric parameter that indicates whether SDUs

detected as erroneous shall be delivered or not.

0 no

1 yes

2 no-detect

3 subscribed value

Other values are reserved.

<Transfer delay> a numeric parameter (0,1,2,…) that indicates the targeted time

between request to transfer an SDU at one SAP to its delivery at the other SAP, in

milliseconds. If the parameter is set to ‘0’ the subscribed value will be requested (refer

3GPP TS 24.008 subclause 10.5.6.5).

<Traffic handling priority> a numeric parameter (1,2,3,…) that specifies the relative

importance for handling of all SDUs belonging to the UMTS bearer compared to the

SDUs of other bearers. If the parameter is set to ‘0’ the subscribed value will be

requested (refer 3GPP TS 24.008 subclause 10.5.6.5).

<Source Statistics Descriptor> Supported in R7 P S a numeric parameter that

specifies characteristics of the source of the submitted SDUs for a PDP context. This

parameter should be provided if the Traffic class is

specified as conversational or streaming (refer 3GPP TS 24.008 subclause 10.5.6.5).

0 Characteristics of SDUs is unknown (default value)

1 Characteristics of SDUs corresponds to a speech source

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды