Fibocom L860-GL Скачать руководство пользователя

Страница: 116 / 254

FIBOCOM L860 AT Commands User Manual

Page 116 of 254

Command

Description

The

TE can choose to register a subset of the MT default profile, typically omitting facilities

also supported by the TE profile. Default value is the MT default profile.

5 Refers to a conflict between the TE profile and the list of MT only facilities.

Note:

Value 5 for <profile_storage> will be supported only in response direction.

string type in hexadecimal character format. The profile describing the supported

USAT

facilities of the referenced <profile_storage> as specified for the Terminal Profile in

3GPP

TS 31.111 [92].

<conflict_profile>

Is string type in hexadecimal character format. A bitwise AND of two profiles, showing

the conflicts, that is, USAT facilities supported by both profiles. See description of

Terminal Profile in 3GPP TS 31.111 [92].

Example

Reference

3GPP TS 27.007

7.1.3 +CUSATD, Profile download upon start-up

This command is used to determine to download which USAT profile during next bootup.

This command determines if, and optionally which profile should be downloaded to the UICC

automatically upon startup. If, prior to a restart/start-up, the +CUSATD settings have not been altered,

then the default settings determine the behaviour upon start-up.

However, if the parameters of +CUSATD has been set to other than default and then a restart is

performed (e.g. by +CFUN), these values determine the behaviour. This is true for one restart only after

alCUSATD parameters as they are always reset to default at the end of the next UICC start-up (i.e.

when the USIM initialisation as specified in 3GPP TS 31.102 [98] has been completed).

The command without parameters resets the parameters to their default values.

The command can be used if the UICC is already in active state upon +CUSATA and the UICC does not

support the "Additional TERMINAL PROFILE after UICC activation" feature (see 3GPP TS 31.111 [92]).

+CUSATD=<download>,1 also enables the unsolicited result code +CUSATS: <UICC_state>. The MT

uses this unsolicited result code to indicate that a profile download is performed (sCUSATD=0,1 or

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды