Fibocom L860-GL страница 192 Скачать руководство пользователя

Страница: 192 / 254

FIBOCOM L860 AT Commands User Manual

Page 192 of 254

Command

Description

2 RFC1144 (applicable for SNDCP only)

3 RFC2507

4 RFC3095 (applicable for PDCP only)

Other values are reserved.

<IPv4AddrAlloc> a numeric parameter that controls how the MT/TA requests to get

the IPv4 address

information

0 IPv4 Address Allocation through NAS Signaling

1 IPv4 Address Allocated through DHCP

<emergency_indication> a numeric parameter used to indicate whether the PDP

context is for emergency bearer

services or not.

0 PDP context is not for emergency bearer services

1 PDP context is for emergency bearer services

<P-CSCF_discovery> a numeric parameter influences how the MT/TA requests to get

the P-CSCF address, see 3GPP TS 24.229 [89] annex B and annex L

0 Preference of P-CSCF address discovery not influenced by +CGDCONT

1 Preference of P-CSCF address discovery through NAS Signaling

<IM_CN_Signaling_Flag_Ind> a numeric parameter used to indicate to the network

whether the PDP context is for IM CN subsystem-related signaling only or not.

0 UE indicates that the PDP context is not for IM CN subsystem-related signaling

only

1 UE indicates that the PDP context is for IM CN subsystem-related signaling only

Note:

The parameters <IPv4AddrAlloc>,<IM_CN_Signaling_Flag_Ind>,and

<P-CSCF_discovery>, can be over-ridden by AT+XPCO command (meaning

AT+CGDCONT values for these parameters can be over-ridden by issuing

AT+XPCO later).

Example

AT+CGDCONT?

OK // Only without any set command.

AT+CGDCONT=1, “IP”,”CMNET”

AT+CGDCONT=2, “IP”,”CMWAP”

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды