Fibocom L860-GL Скачать руководство пользователя страница 200

Страница: 200 / 254

FIBOCOM L860 AT Commands User Manual

Page 200 of 254

Command

Description

request to use GPRS.

<called_address> String that identifies the called party in the address space

applicable to the PDP. For communications software that does not support arbitrary

characters in the dial string, a numeric equivalent may be used. Also, the comma

character "," may be used as a substitute for the period character ".".

For PDP type OSP: IHOSS, the following syntax may be used for

<called_address>: [<host>] [@[<port>] [@

[<protocol>]]] where <host>, <port> and <protocol> are defined in

“+CGDCONT,Define PDP Context”.

For communications software that does not support arbitrary characters in the dial

string, a numeric value equivalent to the host name may be used. However, this

should

be avoided if at all possible.

<L2P> String variable which indicates the layer 2 protocol to be used.

For communications software that does not support arbitrary characters in the dial

string, the following numeric equivalents are used:

0 NULL

1 PPP

2 PAD

3 X25

9 yyyy M-xxxx

Other values are reserved and result in an ERROR response to the Set command.

Note:

V.250 (and certain communications software) do not permit arbitrary

characters in the dial string. The <L2P> and <called_address> strings are

therefore specified as containing digits (0-9) only.

<cid>: Digit string which specifies a particular PDP context definition (See

“+CGDCONT, Define PDP Context”).

Example

AT+CGDCONT?

+CGDCONT: 1,"IP","3GNET","10.168.15.100",0,0,0,0,0,0

+CGDCONT: 2,"IP","3GNET","10.227.131.75",0,0,0,0,0,0

ATD*99***2#

CONNECT

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды