Fibocom L860-GL Скачать руководство пользователя

Страница: 87 / 254

FIBOCOM L860 AT Commands User Manual

Page 87 of 254

AT+CNMA send acknowledgment to network , Two conditions must be met AT+CSMS=1

command set <service> to 1, AT+CNMI=,2 command set <mt> to 2 or AT+CNMI=,,1 command

set <ds> to 1. After the two conditions are met, If the Modem does not receive acknowledgment

after receiver a SMS within the required time, CNMI parameters will NOT be reset automatically

and the +CMT or +CDS unsolicited response will send to the TE again.

Command

Description

Set

[Function]

This command acknowledge the receipt of a +CMT and +CDS response from the

terminal to the Modem.

[Syntax]

For text mode (+CMGF=1)

AT+CNMA

For PDU mode (+CMGF=0)

AT+CNMA[=<n>[,<length>[<CR>PDU<ctrl-Z/ESC>]]]

[Response/Action]

or:

+CME ERROR: <err>

Read

N/A

Test

[Function]

This command returns the list of supported values.

[Syntax]

AT+CNMA=?

[Response/Action]

OK in text mode

or:

+CNMA: (list of supported <n>s) in PDU mode

Parameters

<n>

0 command operates similarly as defined for the text mode

1 send RP-ACK

2 send RP-ERROR

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды