Fibocom L860-GL Скачать руководство пользователя страница 108

Страница: 108 / 254

FIBOCOM L860 AT Commands User Manual

Page 108 of 254

The Set command selects the service or service preference used to send SMS messages. The

value that is set is not retained after a power cycle.

Command

Description

Set

[Function]

The Set command selects the service or service preference used to send SMS

messages. The value that is set is not retained after a power cycle.

[Syntax]

AT+CGSMS=[<service>]

[Response/Action]

or:

+CME ERROR: <err>

Read

[Function]

The Read command displays the current SMS service preference setting.

[Syntax]

AT+CGSMS?

[Response/Action]

+CGSMS: <service>

Test

[Function]

The Test command displays a list of currently available <service>s on the network.

[Syntax]

AT+CGSMS=?

[Response/Action]

+CGSMS: (list of currently available<service>s)

Parameters

Indicates the service or service preference to be used.

0 GPRS

1 Circuit switched (default)

2 GPRS preferred (use circuit switched if GPRS is not available)

3 Circuit switched preferred (use GPRS if circuit switched is not available)

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды