Fibocom L860-GL Скачать руководство пользователя страница 231

Страница: 231 / 254

FIBOCOM L860 AT Commands User Manual

Page 231 of 254

Command

Description

+CGEV: NW DETACH

The network has forced a PS detach. This implies that all active contexts have b

een deactivated. These are not reported separately. ETSI

3GPP TS 27.007 version 7.6.0 Release 7 147 ETSI TS 127 007 V7.6.0 (2010-04)

+CGEV: ME DETACH

The mobile termination has forced a PS detach. This implies that all active conte

xts have been deactivated. These are not reported separately.

+CGEV: NW CLASS <class>

The network has forced a change of MT class. The highest available <class> is r

eported (see +CGCLASS).

+CGEV: ME CLASS <class>

The mobile termination has forced a change of MT class. The highest available <

class> is reported (see +CGCLASS).

+CGEV: ME PDN ACT <cid>[,<reason>[,<cid_other>]]

The mobile termination has activated a context. The context represents a PDN c

onnection in LTE or a Primary

PDP context in GSM/UMTS. The <cid> for this context is provided to the TE. This ev

ent is sent either in result

of explicit context activation request (+CGACT), or in result of implicit context activati

on request associated to

attach request (+CGATT=1). The format of the parameters <cid>, <cid_other> are fou

nd in cCGDCONT.

<reason> integer type parameter indicates the reason why the context activation req

uest for PDP type IPv4v6 was

not granted. This parameter is only included if the requested PDP type associated wit

h <cid> is IPv4v6, and the

PDP type assigned by the network for <cid> is either IPv4 or IPv6.

0 IPv4 only allowed

1 IPv6 only allowed

2 single address bearers only allowed.

3 single address bearers only allowed and MT initiated context activation for a secon

d address type bearer was not successful.

Example

AT+CGEREP=2,1

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды