Fibocom L860-GL Скачать руководство пользователя страница 41

Страница: 41 / 254

FIBOCOM L860 AT Commands User Manual

Page 41 of 254

Command

Description

0x92 0x40 memory problem

0x94 0x00 no EF selected

0x94 0x02 out of range (invalid address)

0x94 0x04 file ID not found; pattern not found

0x94 0x08 file is inconsistent with the command

0x98 0x02 no CHV initialized

0x98 0x04 access cond. Not fullfiled / unsucc. CHV verify

authent.failed

0x98 0x08 in contradiction with CHV status

0x98 0x10 in contradiction with invalidation status

0x98 0x40 unsucc. CHV-verif. Or UNBLOCK CHF / CHV blocked /UNBL.blocked

0x98 0x50 increases can not be performed. Max. value reached

0x61 0xXX SW2 indicates the number of response bytes still available. Use GET

RESPONSE to access this data.

0x62 0xXX Warning - state unchanged

0x62 0x00 Warning - no information provided

0x62 0x81 Warning - part of returned data may be corrupt

0x62 0x82 Warning - end of file/record reached (bad cmd)

0x62 0x83 Warning - selected file invalidated

0x62 0x84 Warning - bad file control information format

0x63 0xXX Warning - state unchanged

0x63 0x00 Warning - no information provided

0x63 0x81 Warning - file filled up with last write

0x63 0xCx Warning - counter value is x

0x64 0xXX Error - state unchanged

0x65 0xXX Error - state changed

0x65 0x00 Error - no information provided

0x65 0x81 Error - memory failure 66 xx Security Error

0x66 0xXX Security Error

0x67 0xXX incorrect parameter P3

0x68 0xXX Check Error - CLA function not supported

0x68 0x00 Check Error - no information provided

0x68 0x81 Check Error - logical channel not supported

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды