Fibocom L860-GL страница 191 Скачать руководство пользователя

Страница: 191 / 254

FIBOCOM L860 AT Commands User Manual

Page 191 of 254

Command

Description

supported<emergency_indication>s),(list of supported <PCSCF_discovery>s),(list of

supported <IM_CN_Signaling_Flag_Ind>s)[...]]

Parameters

<cid> Numeric parameter specifying a particular PDP context definition (PDP

Context Identifier). The parameter is local to the Terminal-Mobile Terminal interface

and is used in other PDP context-related commands. The value is from 0 to 29

<"PDP_type"> (Packet data protocol type) String parameter (in quotation marks)

specifying the type of packet data protocol: IP

Internet Protocol (IETF STD 5)

IPV6

Internet Protocol, version 6 (IETF RFC 2460)

IPV4V6 Virtual<PDP_type>introduced to handle dual IP stack capability

Note:

The<PDP_type>is IPV6 and IPV4V6 are supported only is the feature FEAT_IPV6

support is enabled

<"APN"> (Access Point Name)

String parameter (in quotation marks), which is a

logical name that is used to select the GGSN or the external packet data network. If

the value is null or omitted, the subscription value is requested.

<"PDP_address"> String parameter (in quotation marks), which identifies the ME in

the address space applicable to the PDP.

If the value is null or omitted, a value may be provided by the terminal during the PDP

start up procedure or, failing that, a dynamic address is requested.

The Read form of the command continues to return the null string even if an address

has been allocated during the PDP start up procedure. The allocated address may be

read using the +CGPADDR command.

The default value is 0.

<d_comp> Numeric parameter that controls PDP data compression.

0 off (default if value is omitted) (L810-00-06 only support off option)

1 on (manufacturer preferred compression)

2 V.42 bis

Other values are reserved. The default value is 0.

<h_comp>

a numeric parameter that controls PDP header compression

0 off (default if value is omitted)

1 on (manufacturer preferred compression)

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды