Fibocom L860-GL Скачать руководство пользователя страница 79

Страница: 79 / 254

FIBOCOM L860 AT Commands User Manual

Page 79 of 254

Command

Description

[Syntax]

AT+CSMP=?

[Response/Action]

Parameters

<fo>

Depending on the command or result code: first octet of 3GPP TS 23.040 [3]

SMS-DELIVER, SMS-SUBMIT(default 17), SMS-STATUS-REPORT, or

SMS-COMMAND(default 2) in integer format.

<vp>

Validity Period, depending on SMS-SUBMIT <fo>,

TP-Validity-Period-Format bits setting.

If there is no correlation between the VPF and the VP value. an error message will be

returned.

Either in integer format (see Table) or in time-string format ("yy/MM/dd,

hh:mm:ss±zz"). If in integer format the vp will write to SIM EF and read form SIM EF

when use it.

<pid>

Protocol-Identifier. The one octet information element by which the SM-TL

either refers to the higher layer protocol being used, or indicates interworking with a

certain type of telematic device.

"0 - no interworking, SME-to-SME protocol (default) "Any value between 0-255 will be

accepted.

The SC may reject messages with a TP-Protocol-Identifier containing a reserved

value or one, which is not supported.

<dcs>

One octet of Data Coding Scheme, indicates the data coding scheme of the

DATA, and may indicate a message class.

Note:

For DCS expanded information, see section “DCS handling”.

default alphabet: 00xx00xx, 111 100xx, 1 101xxxx

8 bit data: 00xx01xx, 111101xx

UCS2: 00xx10xx, 1110xxxx

reserved: 00xx11xx, 0100xxxx-1011xxxx

The default value at power-up is 0 - Default alphabet.

Example

AT+CSMP?

+CSMP: 17,167,0,0 (default values for SMS-SUBMIT)

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды