Fibocom L860-GL Скачать руководство пользователя

Страница: 46 / 254

FIBOCOM L860 AT Commands User Manual

Page 46 of 254

Command

Description

[Syntax]

AT+CFUN?

[Response/Action]

+CFUN: <power mode>, <STK_mode>

+CME ERROR: <err>

Test

[Function]

The Test command displays the list of supported functionality settings.

[Syntax]

AT+CFUN=?

[Response/Action]

+CFUN: (list of supported <fun>s), (list of supported <rst>s)

+CME ERROR: <err>

Parameters

<fun>

Functionality levels:

0 Turn off (With logging out network).

1 Full functionality meaning start up MS(from offline mode)

4 Disables phone transmit & receive RF circuits – Flight mode.

6 Enables the SIM-toolkit interface and fetching of proactive commands by

SIM-APPL from the SIM-card.

7 Disables the SIM-toolkit interface and fetching of proactive commands by

SIM-APPL from the SIM-card.

8 Disable fetching of proactive commands by SIM-APPL from the SIM-card.

15 Mode to simulate reset (this will reset MS including SIM)

16 Mode to perform hidden reset (this will reset MS without resetting SIM).

27 Mode to perform reset of SIM and restore previous PIN validation state (this will

reset SIM without resetting MS).

31 Mode to Disable Single Stack with an option to Power-Off/Power-On Single (U)SIM

card.

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды