Fibocom L860-GL Скачать руководство пользователя

Страница: 131 / 254

FIBOCOM L860 AT Commands User Manual

Page 131 of 254

Command

Description

Test

[Function]

The Test command returns a list of pairs which represent the available facilities, and the

maximum length of their passwords.

[Syntax]

AT+CPWD=?

[Response/Action]

+CPWD: list of Supported (<fac>,<pwdlength>)s

or:

+CME ERROR: <err>

Parameters

<fac>

Description

SC SIM (lock SIM/UICC card) (SIM/UICC asks password in MT power-up and when

this lock command issued)

FD SIM card or active application in the UICC (GSM or USIM) fixed dialling memory

feature (if PIN2 authentication has not been done during the current session, PIN2 is

required as <passwd>)

AO BAOC (Bar All Outgoing Calls)

OI BOIC (Bar Outgoing International Calls)

OX BOIC-exHC (Bar Outgoing International Calls except to Home Country)

AI BAIC (Bar All Incoming Calls)

IR BIC-Roam (Bar Incoming Calls when Roaming outside the home country)

AB All Barring services (applicable only for <mode>=0)

AG All outgoing barring services (applicable only for <mode>=0)

AC All incoming barring services (applicable only for <mode>=0)

P2 SIM PIN2

<fac>

List of supported facilities. All the facility messages, except for SC and P2,

are sent to the network. (The facilities are not case-sensitive.)

Please see <fac> Table.

String type, 4-8 character old password specified for the facility from the

Modem user interface.

<newpwd> String type, 4-8 character new password specified by the user.

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды