Fibocom L860-GL Скачать руководство пользователя страница 238

Страница: 238 / 254

FIBOCOM L860 AT Commands User Manual

Page 238 of 254

Command

Description

+CGSCONTRDP: <cid>,<p_cid>,<bearer_id>[,<IM_CN_Signalling_Flag>]

[<CR><LF>+CGSCONTRDP: <cid>,<p_cid>,<bearer_id>[,<IM_CN_Signalling_Flag>]

[...]]

Read

N/A

Test

[Function]

The test command returns a list of <cid>s associated with active contexts

[Syntax]

AT+CGSCONTRDP=?

[Response/Action]

+CGSCONTRDP: (list of <cid>s associated with active contexts)

Parameters

<cid>:

a numeric parameter which specifies a particular PDP context or Traffic Flows

definition.

The parameter is local to the TE-MT interface and is used in other PDP context-related

commands.

<p_cid>:

a numeric parameter which specifies a particular PDP context definition or default EPS

context Identifier which has been specified by use of the +CGDCONT command. The

parameter is local to the TE-MT interface.

<bearer_id>:

a numeric parameter which identifies the bearer, EPS Bearer in EPS and NSAPI in

UMTS/GPRS.

<IM_CN_Signalling_Flag>:

A numeric parameter used to show whether the PDP context is for IM CN subsystem-

related signalling only or not.

0 PDP context is not for IM CN subsystem-related signalling only

1 PDP context is for IM CN subsystem-related signalling only

Note :

<IM_CN_Signalling_Flag> parameter is supported only from release

10.

Note 1:

Parameters for network initiated PDP contexts are returned as well.

The dynamic part of the PDP context will only exist if established by the

network.

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды