Fibocom L860-GL Скачать руководство пользователя страница 150

Страница: 150 / 254

FIBOCOM L860 AT Commands User Manual

Page 150 of 254

<lac>, <ci>, <AcT> and <rac>, if available, are returned only when <n>=2 and MT is registered in the

network.

Test command returns the range of supported network registration mode (i.e. <n>).

Command

Description

Set

[Function]

The Set command controls the presentation of an unsolicited result code "+CGREG: "

and the result of the Read operation.

[Syntax]

AT+CGREG=<n>

[Response/Action]

or:

+CME ERROR: <err>

Read

[Function]

The read command returns the status of result code presentation and an integer

<stat>which shows whether the network has currently indicated the registration of the

MT.

[Syntax]

AT+CGREG?

[Response/Action]

+CGREG: <n>, <stat>[,<lac>[,<ci>[,<AcT>[,<rac>[,<reject type>[,<reject cause>]]]]]]

Test

[Function]

The Test command displays the supported values of <n>.

[Syntax]

AT+CGREG=?

[Response/Action]

+CGREG: (list of supported <n>s)

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды