Fibocom L860-GL Скачать руководство пользователя страница 222

Страница: 222 / 254

FIBOCOM L860 AT Commands User Manual

Page 222 of 254

code is displayed on TE. In error case the final result code NO CARRIER or CME

ERROR :<error> is displayed. PS attachment and PDP context activation procedures may take

place prior to or during the PDP startup if they have not already been performed using the

+CGATT and +CGACT commands.

If no <cid> is given or if there is no matching context definition, the MT shall attempt to activate the context

with whatever information is available to the MT. The other context parameters shall be set to their default

values.

If the activation is successful, data transfer may proceed. After data transfer is complete, and the layer 2

protocol termination procedure has completed successfully, the V.250 command state is re-entered and

the MT returns the final result code OK.

Command

Description

Set

[Function]

Set command specifies the <L2P> and <cid> to establish data call (csd connection

state)

[Syntax]

AT+CGDATA = [<L2P> ,[<cid> [,<cid> [,…]]]]

[Response/Action]

CONNECT

It follows data transfer

CME ERROR: <error>

Read

N/A

Test

[Function]

Test command returns values supported as a compound value.

[Syntax]

AT+CGDATA =?

[Response/Action]

+CGDATA: (list of supported <L2P>s)

Parameters

<L2P> a string parameter that indicates the layer 2 protocol to be used between the

TE and MT

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды