Fibocom L860-GL Скачать руководство пользователя страница 198

Страница: 198 / 254

FIBOCOM L860 AT Commands User Manual

Page 198 of 254

Command

Description

AT+CGATT?

[Response/Action]

+CGATT: <state>

Test

[Function]

The Test command requests information on the supported GPRS service states.

[Syntax]

AT+CGATT=?

[Response/Action]

+CGATT: (list of supported <state>s)

Parameters

<state> Indicates the state of the GPRS attachment:

0 Detached.

1 Attached.

Example

AT+CGATT=?

+CGATT: (0,1)

AT+CGATT?

+CGATT: 0

AT+CGATT=0

Reference

3GPP TS 27.007

11.2.6 D*99, Request GPRS Service "D"

This command enables the ME to perform the actions necessary for establishing communication between

the terminal and the external Packet Data Network (PDN).

The ITU V.25ter 'D' (Dial) command causes the ME to enter the ITU V.25ter Online Data state and

together with the terminal, to start the specified layer 2 protocol. The ME returns CONNECT to confirm

acceptance of the command prior to entering the ITU V.25ter Online Data state. No further commands

may follow on the AT command line.

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды