Fibocom L860-GL страница 68 Скачать руководство пользователя

Страница: 68 / 254

FIBOCOM L860 AT Commands User Manual

Page 68 of 254

Command

Description

Test

[Function]

Test command returns list of the supported (on/off)s. If the reporting is enabled, the

MT returns the URC whenever the time zone is changed.

[Syntax]

AT+ CTZR=?

[Response/Action]

+CTZR: (list of supported < reporting >s)

Parameters

< reporting >

integer type value indicating:

0 disable time zone change event reporting

1 Enable time zone change event reporting by unsolicited result code +CTZV: <tz>.

2 Enable extended time zone and local time reporting by unsolicited result code

+CTZE: <tz>,<dst>,[<time>].

3 Enable extended time zone and universal time reporting by unsolicited result code

+CTZEU: <tz>,<dst>,[<utime>].

Note: <reporting>=3 is supported only when CAT_R13_SUPPORT is enabled in the

build config.

<tz>

integer value indicating the time zone.

<time>

string type value; format is "Yy/MM/dd,hh:mms" ,wherein characters indicates year,

month, day, hour, minutes, seconds.

<dst>

daylight savings time value:

0 No adjustment for Daylight Saving Time

1 +1 hour adjustment for Daylight Saving Time

2 +2 hours adjustment for Daylight Saving Time

string type value representing the sum of the local time zone (difference between the

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды