Fibocom L860-GL Скачать руководство пользователя

Страница: 166 / 254

FIBOCOM L860 AT Commands User Manual

Page 166 of 254

Command

Description

[Syntax]

AT+CEMODE?

[Response/Action]

+CEMODE : <mode>

Test

[Function]

The test command is used for requesting information on the supported MT mode of

operation.

[Syntax]

AT+CEMODE=?

[Response/Action]

+CEMODE: (list of supported <mode>s)

Parameters <mode>:

a numeric parameter which indicates the mode of operation

0 PS mode 2 of operation

1 CS/PS mode 1 of operation

2 CS/PS mode 2 of operation

3 PS mode 1 of operation

Note:

The definition for UE modes of operation can be found in 3GPP TS 24.301 [83]

Other values are reserved and will result in an ERROR response to the set command.

For L830-GL-01:

The default setting of <mode> is 1.

For L810-GL-00,L811-EA-00,L830-EA-00,L830-GL-00,L831-EA-00/01:

The default setting of <mode>is 2.

Example

AT+CEMODE=?

+CEMODE: (0-3)

AT+CEMODE?

+CEMODE: 2

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды