Fibocom L860-GL Скачать руководство пользователя

Страница: 197 / 254

FIBOCOM L860 AT Commands User Manual

Page 197 of 254

Command

Description

AT+CGQREQ?

+CGQREQ: 1,2,4,3,9,10

+CGQREQ: 2,2,4,3,9,10

AT+CGQREQ=1,0,,0,0,10

AT+CGQREQ?

+CGQREQ: 1,0,4,0,0,10

+CGQREQ: 2,2,4,3,9,10

Reference

3GPP TS 27.007

11.2.5 +CGATT, GPRS Attach or Detach

This command attaches/detaches the ME to/from the GPRS service. When the command has completed,

the ME remains in V.25ter command state. If the ME is already in the requested state, the command is

ignored and the OK response is returned. If the requested state cannot be achieved, an ERROR or +CME

ERROR response is returned. Extended error responses are enabled by the +CMEE command. Any

active PDP contexts will be automatically deactivated when the attachment state changes to detached.

Command

Description

Set

[Function]

The Set command attaches/detaches the ME to/from the GPRS service.

[Syntax]

AT+CGATT=<state>

[Response/Action]

or:

+CME ERROR: <err>

Read

[Function]

The Read command returns the current GPRS service state.

[Syntax]

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды