Fibocom L860-GL Скачать руководство пользователя страница 98

Страница: 98 / 254

FIBOCOM L860 AT Commands User Manual

Page 98 of 254

Command

Description

If text mode (+CMGF=1) command execution is successful and SMS-SUBMIT:

+CMGR:

If text mode (+CMGF=1) command execution is successful and SMS-COMMAND:

+CMGR:

<stat>,<fo>,<ct>[,<pid>[,<mn>][,<da>][,<toda>],<length><CR><LF><cdata>]

If text mode (+CMGF=1) command execution is successful and CBM storage:

+CMGR:

If text mode (+CMGF=1) command execution is successful and

SMS-STATUS-REPORT:

+CMGR:

If PDU mode (+CMGF=0) and command execution is successful:

+CMGR:

otherwise:

+CMS ERROR: <err>

Read

N/A

Test

[Function]

This command only returns OK.

[Syntax]

AT+CMGR=?

[Response/Action]

Parameters

<index> Index in storage of the message to be retrieved.

<stat>

Status of message in memory:

PDU mode

Text mode

Description

“REC UNREAD”

Received unread messages

“REC READ”

Received read messages

“STO UNSENT”

Stored unsent messages

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Бренды по названию

Популярные бренды