Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 99

Страница: 99 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

5. Remove the foot of Right PG Torsion Spring from Tab A, and release the coil

section from Tab B to remove the Right PG Torsion Spring from the Main Frame.

Figure 4-61. Removing the Right PG Torsion Spring

6. Remove CR Shaft Mounting Plate Fixed Spring from the tab and cutout on the

Main Frame, and draw out the spring in the direction of the arrow.

Figure 4-63. Removing the CR Shaft Mounting Plate Fixed Spring

Place the feet of Left PG Torsion Spring and Right PG Torsion
Spring on the Carriage Shaft.

Figure 4-62. Installing the PG Torsion Springs

Right PG Torsion Spring

Tab A

Tab B

Foot

Left Side

Foot

Right Side

Insert the foot of CR Shaft Mounting Plate Fixed Spring into the
cutout of the Main Frame (rear side).

See Figure 4-63.

Cutout (rear side)

Tab

CR Shaft Mounting Plate Fixed Spring

Cutout

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 99 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: