manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 28 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 28

EPSON Stylus Photo 1390/1400/1410

Revision B

OPERATING PRINCIPLES

Printer Mechanism

28

2.2.3.2  CD/DVD Tray Base Lock Mechanism

To prevent the Printhead from being damaged by mistake, the printer is designed to 
lock the CD/DVD Tray Base when the Carriage Unit is out of its home position.

The following explains the lock mechanism of the CD/DVD Tray Base.

†

Lock Release Sequence

1. When the Carriage Unit returns to its home position, the Pump Motor drive is 

transmitted to the Paper EJ Lock Release Cam.

2. The salient of the Cam presses down the Paper EJ Transmission Lock Lever 

to release the tab of the Paper EJ Lock Lever from the Paper EJ Transmission 
Lock Lever.

3. The CD-R Release Lever comes free from the Paper EJ Lock Lever and 

comes down to enable the CD/DVD Tray Base to open.

When the Carriage Unit is out of its home position, the salient of the Paper EJ Lock 
Release Cam does not press down the Paper EJ Transmission Lock Lever, and the tab 
of the Paper EJ Lock Lever is not released. Therefore, the CD/DVD Tray Base cannot 
be opened.

Figure 2-6.   CD/DVD Tray Base Lock Mechanism

C H E C K

P O I N T

The Stylus Photo 1390 is not equipped with CD/DVD related units.

CD/DVD Tray Base

Paper EJ Lock 
Release Cam

Salient

Paper EJ 
Transmission 
Lock Lever

Paper EJ Lock 
Lever

Jointed Position

Tab

CD-R Release Lever

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов