Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 124

Страница: 124 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

124

4.2.8 Removing the Sensors

4.2.8.1 PE Sensor Holder

Remove the ASF Assy. See Section 4.2.4 on page 86.

2. Remove the PE Sensor Connector Cable from the five tabs on the Release Holder

Assy and the two tabs on the Head Cable Cover.

Figure 4-137. Releasing the Cables

3. Release the tabs that secure the PE Sensor Holder from the cutout of the Main

Frame with a flat-blade screwdriver, then slide it upwards then toward you to
remove it.

Figure 4-138. Removing the PE Sensor Holder

Tabs

PE Sensor Connector Cable

Tabs

Release Holder Assy

Head Cable Cover

Front

Tab

PE Sensor Holder

Align the four tabs and Guide Pin on the PE Sensor Holder with the
positioning holes on the Main Frame correctly so that there is no
gap between the PE Sensor Holder and the Main Frame.

Figure 4-139. Installing the PE Sensor

Tabs

Guide pin

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 124 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: