Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 61

Страница: 61 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

During printing

After starting to print, ink is not
ejected and paper stops midway.

Head FFC

1. Check that the Head FFC is securely connected to the Print Head

Connector and Main Board Connectors CN10, CN11 and CN12.

1. Connect the Head FFC to the Print Head

Connector and Main Board Connectors CN10,
CN11 and CN12.

2. Check the Head FFC for damages.

2. Replace the Head FFC with a new one.

Ink is not ejected from most
nozzles.

Print Head

1. Check for occurrence of Head Hot.

1. Replace the Print Head with a new one.

Table 3-11. Troubleshooting of Fatal Error

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

Print Head

Connector

Head FFC

CN10, 11, 12

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 61 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: