Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 56

Страница: 56 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

At power-on

At power-on, the Pump Motor
does not operate at all.

Relay Connector
Cable
(for Pump
Motor)

1. Check that the Relay Connector Cable is connected to the Main

Board Connector CN8.

1. Connect the Relay Connector Cable to the

Main Board Connector CN8.

2. Check the Relay Connector Cable for damages.

2. Replace the Relay Connector Cable with a new

one.

While the power-on sequence is
being executed, Fatal error is
displayed.

APG Sensor

1. Check that the APG Sensor Connector cables are connected to

the APG Sensors and Relay Board Connector CN4 and CN5.

1. Connect the APG Sensor Connector cables to

the APG Sensors and Relay Board Connector
CN4 and CN5.

2. Check the APG Sensors for damages.

2. Replace the APG Sensors with new ones.

Table 3-11. Troubleshooting of Fatal Error

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

CN8

CN4

CN5

APG Sensors

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 56 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: