Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 67

Страница: 67 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

The printout is
stained with ink.

The non-printed side or the
bottom of the printout is dirty
with ink.

Front Paper
Guide Pad

1. Check if the Front Paper Guide Pad is installed securely and

evenly in the setting position.

1. If the Ink pads are not securely installed,

reinstall the Front Paper Guide Pad correctly.

When the paper size in the sent
print data is larger than the size
of the fed paper, data is printed
on the Front Paper Guide,
extending off the paper.

PW sensor

1. Check that the PW Sensor FFC is connected.

1. Connect the PW Sensor FFC.

2. Check that the PW Sensor is not faulty.

2. Replace the PW Sensor with a new one.

Ink smudges appear on the blank
area of the printout.

Paper EJ Frame
Assy.

1. Check the Star Wheel Rollers for ink stain.

1. Clean the Star Wheel Rollers with a soft cloth.

Front Paper
Guide

1. Check the Front Paper Guide for ink stain.

1. Clean the Front Paper Guide with a soft cloth.

Table 3-12. Print Quality Troubles

Observed Faults

Details of the Fault

Faulty Part/

Part Name

Check Point

Remedy

Front Paper Guide Pad

Front Paper Guide

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 67 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: