manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 117 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 117

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

117

4.2.6.13  Front Paper Guide and Paper Eject Roller

1. Remove the Paper EJ Frame Assy.

For Stylus Photo 1400/1410:

See section 4.2.1.3 on page 79.

For Stylus Photo 1390:

See section 4.3.1 on page 128.

2. Release the Carriage Lock, and move the Carriage Unit to the center. 

See section 4.2.1.3 on page 79.

3. Remove the EJ Grounding Spring from the Main Frame with tweezers.

Figure 4-116.  Removing the EJ Grounding Spring

4. Remove the Spacer from the EJ Roller Shaft.

5. Remove the Guide Pins on Left Bushing 8 from the Main Frame using tweezers, 

and turn Left Bushing 8 toward you to align with the cutouts on the Main Frame.

Figure 4-118.  Removing the Spacer and Rotating the Left Bushing 8

Referring to 

Figure 4-117

, correctly install the EJ Grounding 

Spring. 

Figure 4-117.  Installing the EJ Grounding Spring

EJ Grounding 

Spring

Insert the Spacer into the groove on the Front Paper Eject Roller.

Guide 

pin

Spacer

Groove

Left Bushing 8

Cutout

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов