manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 30 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 30

EPSON Stylus Photo 1390/1400/1410

Revision B

OPERATING PRINCIPLES

Printer Mechanism

30

2.2.4  Paper Feeding Mechanism

The Paper Feeding Mechanism is designed to transfer the paper fed from the ASF, or 
the CD-R fed from the CD/DVD Tray according to the print data. (The Stylus Photo 
1390 is not equipped with CD/DVD related units.)

2.2.4.1  Paper Feeding Mechanism

The following shows the specifications of the DC motor that drives the Paper Feeding 
Mechanism.

Like the CR Motor, a DC motor is used as the PF Motor in this product.
Closed loop control based on the DC Motor and Rotary Encoder has the following 
advantages.

†

Improved paper feed accuracy

†

Paper feed amount control

The PF Motor drive is transmitted to the PF Roller and the Paper EJ Roller following 
the route shown below. 

The following shows the part names and outline of the drive transmission path. 

Figure 2-8.  Paper Feeding Mechanism

Table 2-6.  PF Motor Specifications

Item

Specifications

Type

DC motor with brushes

Drive voltage

+42V ± 5% (voltage applied to driver)

Armature resistance

21.2

Ω

 ± 10%

Inductance

17.2mH (1kHz)

Rotor Inertia

18.8gcm2

Drive method

PWM

Drive IC

A6628

PF Motor

PF Timing Belt

PF Roller

Spur Gear 31.5

Spur Gear 68

Front Paper Eject Roller

Spur Gear 16; B (front)

Spur Gear 15.5

Rear Paper Eject Roller

Combination Gear 

36.294, 55

Spur Gear 16; B (rear)

Front Paper Guide

PF Roller

PF Motor

Front Paper Eject Roller

Rear Paper Eject Roller

PF Timing Belt

Combination Gear 
36.294, 55

Spur Gear 31.5

Spur Gear 16; 
B (front)

Spur Gear 68

Spur Gear 15.5

Spur Gear 16; B (rear)

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов