manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 57 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 57

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

57

At power-on

While the power-on sequence is 
being executed, Fatal error is 
displayed.

ASF Motor

1. Check that the Connector cable of the ASF Motor is connected to 

the Relay Connector.

1. Connect the Connector cable of the ASF Motor 

to the Relay Connector.

2. Using a tester, check the resistance value of the ASF Motor.

Value of resistance: 7.0

Ω

 ±

 

10%

2. If the resistance value is abnormal, replace the 

ASF Motor with a new one.

3. Check the ASF Motor connector cable for damages.

3. Replace the ASF Motor with a new one.

Relay Connector 
Cable
(for the ASF 
Motor)

1. Check that the Relay Connector Cable is connected to the Main 

Board Connector CN13.

1. Connect the Relay Connector Cable to the 

Main Board Connector CN13.

2. Check the Relay Connector Cable for damages.

2. Replace the Relay Connector Cable with a new 

one.

Table 3-11.  Troubleshooting of Fatal Error

Occurrence 

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

Relay Connector

ASF Motor

CN13

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов