Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 120

Страница: 120 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

120

6. Remove the PG Grounding Spring from the cutout of the Main Frame, and remove

the PF Grounding Spring from the groove of the PF Roller Shaft.

Figure 4-125. Removing the PF Grounding Spring

7. Make sure that the Left Parallelism Adjust Bushing is not protruding from the

cutout of the Main Frame. If it is protruding, loosen the C.B.S. (P4) 3x8 screw that
secures the Left Parallelism Adjust Bushing, and slide it to prevent the Left
Parallelism Adjust Bushing from becoming hooked on the cutout.

Figure 4-126. Rotating the Left Parallelism Adjust Bushing

8. Remove the Guide Pin of Left Bushing 8 from the Main Frame using tweezers,

and rotate the Bushing upwards to align with the cutout on the Main Frame.

Figure 4-127. Rotating the Left Bushing 8

9. Remove the E-ring from the PF Roller Shaft with a flat-blade screwdriver, and

slide Left Bushing 8 to the inside of the Printer Mechanism.

Figure 4-128. Removing the Left Bushing 8

Rear

Cutout

PF Grounding Spring

PF Roller Shaft

Groove

6) C.B.S. (P4) 3x8

(5±1 kgf.cm)

Left Parallelism

Adjust Bushing

Cutout

C A U T I O N

When performing the following procedure, take care not to lose the
E-ring.

Guide pin

Left Bushing 8

Cutout

E-Ring

PF Roller Shaft

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 120 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: