manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 91 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 91

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

91

3. Disconnect all the FFCs and Connector Cables connected to the Board Assy in 

order from the front, then draw out the Board Assy from the Printer taking care of 
the interference between the Manual Paper Guide and the Radiation Plates on the 
Board Assy.

„

CN2: USB Host (PictBridge) (not equipped for Stylus Photo 1390)

„

CN3: Relay Board FFC

„

CN5: Operation Panel FFC

„

CN6: Relay Connector Cable (for CR Motor)

„

CN7: PF Motor Connector Cable

„

CN8: Relay Connector Cable (for Pump Motor)

„

CN9: APG Motor Connector Cable

„

CN10: Head FFC

„

CN11: Head FFC

„

CN12: Head FFC

„

CN13: Relay Connector Cable (for ASF Motor)

„

CN14: CR Encoder Sensor/PW Sensor FFC

„

CN15: CSIC FFC

Figure 4-38.  Removing the Board Assy

FFCs and Connectors

Interference 

point

Board Assy

Manual Paper 

Guide

Radiation Plates

„

Make sure that the FFCs are not crossing each other, and 
connect the FFCs and Connector Cables to the Main Board 
while paying attention to the edges of the Shield Plate.

„

Take care not to put the Board Assy onto the three Ground 
Plates.

Figure 4-39.  Installing the Board Assy (1)

„

When installing the FFC to the connector (CN15), secure it 
with acetate tape as shown below. 

Figure 4-40.  Installing the Board Assy (2)

Grounding Plates

3mm

FFC

CN15

Acetate Tape

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов