Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 59

Страница: 59 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

At power-on

At power-on, the Carriage Unit
moves away from the home
position and bumps against the
right of the Frame, then hits the
left of the Frame.

Sensor FFC

1. Check that the Sensor FFC is connected to the CR Encoder

Sensor Board Connector and Main Board Connector CN14.

1. Connect the Sensor FFC to the CR Encoder

Sensor Board Connector and Main Board
Connector CN14.

2. Check the Sensor FFC for damages.

2. Replace the Sensor FFC with a new one.

At power-on, the PF Roller
rotates fast about a half turn.

PF Encoder
Sensor Holder

1. Check that the PF Encoder Sensor Holder is mounted correctly.

1. Install the PF Encoder Sensor Holder correctly.

2. Check that the FFC of the PF Encoder Sensor is securely

connected to the PF Encoder Sensor Board Connector and Relay
Board Connector CN6.

2. Connect the PF Encoder Sensor FFC to the PF

Encoder Sensor Board and Relay Board
Connector CN6.

3. Check the PF Encoder Sensor for paper dust, etc.

3. Remove the paper dust, etc. from the PF

Encoder Sensor.

4. Check if the PF Encoder or the FFC is damaged.

4. Replace the PF Encoder with a new one.

Table 3-11. Troubleshooting of Fatal Error

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

CN14

CR Encoder Sensor

Board Connector

CN6

PF Encoder Sensor

Board Connector

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 59 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: