manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 138 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 138

EPSON Stylus Photo 1390/1400/1410

Revision B

ADJUSTMENT

Adjustment

138

5.2.1.1  PF Belt Tension Adjustment Method

1. Secure the PF Motor to the Printer Mechanism, and install the Drive Belt on the 

Gear of the PF Scale and the Pinion Gear of the PF Motor.

2. Press the [POWER] button. The LCD of the Measuring Tool displays No. 0 and 

No. 1.

3. Select the channel from among No. 0 to No. 9 by pressing the [SELECT] button. 

(The initial value can be selected as the channel.)

4. Press the [WEIGHT] button. The initial value will be displayed. Enter "1.2g/m" 

with the ten-key pad.

5. Press the [WIDTH] button. The initial value will be displayed. Enter "5.0 mm" 

with the ten-keypad.

6. Press the [SPAN] button. The initial value will be displayed. Enter "48mm" with 

the ten-keypad.

7. Bring the microphone as close as possible to the center of the Timing Belt.

Figure 5-2.  Microphone Position

8. Press the [MEASURE] button. ("----" is displayed on the LCD screen.)

9. Put the tip of the tweezers on the Drive Belt, and flip it downward in that position. 

The "----" displayed on the LCD will become wave pattern during the 
measurement. When it has finished, the measurement result will be displayed by 
"N" (Newton) after the beep. This jig can pick up and measure the sounds 
accurately, regardless of the flipping force.

10. Repeat 

Step 8

 to 

Step 9

, and delicately shift the variable mounting position of the 

PF Motor to adjust the tension until the tension falls within the specified value.

C A U T I O N

The measurement must be carried out in a silent environment. 
Otherwise the microphone of the measuring tool may pick up the 
noise around it and the right adjustment value cannot be obtained.

C A U T I O N

As the Drive Belt is flipped with the tip of tweezers in the following 
steps, carefully choose the flipping position so that the Belt will not 
make contact with the microphone by reaction of flipping.

Microphone of Measuring Tool

Timing Belt

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов