manualshive.com logo in svg

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 103 / 168

Поделиться
Скачать
Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 103

EPSON Stylus Photo 1390/1400/1410

Revision B

DISASSEMBLY AND ASSEMBLY

Disassembly/Assembly Procedures

103

18. To prevent the CR Scale Cover from interfering with the back of the Carriage 

Unit, slide the Carriage unit to the left side, shift the Carriage Shaft to the left 
direction to remove the Carriage Shaft from both the Main Frame and the Carriage 
Unit, release the right end from the Main Frame, and draw out the Carriage shaft.

Figure 4-76.  Removing the Carriage Shaft

19. Remove the CR Drive Belt from the Carriage Unit.

Figure 4-78.  Removing the CR Drive Belt

C A U T I O N

When performing the following procedure, take care not to scratch 
the Carriage Shaft.

Interference 

point

1

2

3

Carriage

Unit

Carriage Shaft

CR Scale Cover

„

Set the longer end of the Carriage Shaft to the left side.

„

When the Carriage Shaft is removed, the Plain Spring and Leaf 
Spring that are attached to the right end of the Carriage Shaft 
may drop off. In such case, be sure to attach them in the order 
as shown in the figure below

Figure 4-77.  Installing the Carriage Shaft

Refer to the figure below and install the CR Drive Belt so that its 
top and rear sides face the correct way.

Figure 4-79.  Installing the CR Drive Belt

Leaf Spring

Plain Spring

Carriage Shaft

Left Side

Right 

Side

Longer

Shorter

Carriage Unit

CR Drive Belt

With Tooth Surface

Without Tooth Surface

Both Surfaces have Tooth

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Отзывы:

Нет отзывов