Epson 1400 - Stylus Photo Color Inkjet Printer Скачать руководство пользователя страница 68

Страница: 68 / 168

EPSON Stylus Photo 1390/1400/1410

Revision B

TROUBLESHOOTING

Overview

The printout is
stained with ink.

Ink smudges appear on the blank
area of the printout.

Front and Rear
Paper EJ Roller
Assys

1. Check the Front and Rear Paper EJ Roller Assys for ink stain.

1. Clean the Front and Rear Paper EJ Roller Assys

with a soft cloth.

Driven Roller
Shaft

1. Check the Driven Roller Shaft for ink stain.

1. Clean the Driven Roller Shaft with a soft cloth.

Ink System Unit

1. Check that wiping operation was performed properly.

1. Install the Cleaner blade correctly or replace it

with a new one.

Table 3-12. Print Quality Troubles

Observed Faults

Details of the Fault

Faulty Part/

Part Name

Check Point

Remedy

Driven Roller Shaft

Rear Paper EJ Roller Assy

Front Paper EJ Roller Assy

Cleaner Blade

Содержание 1400 - Stylus Photo Color Inkjet Printer









































































































































































Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы:

Epson 1400 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию, Страница: 68 / 168

Результаты поиска

Содержание 1400 - Stylus Photo Color Inkjet Printer

Отзывы: